- ×
8 Channel SSR G3MB-202P Solid State Relay Module1 × ₨1,800 - ×
WeMos D1 Mini NodeMcu 4M ESP82661 × ₨950
Subtotal: ₨2,750
Development Boards
Showing 97–120 of 146 resultsSorted by popularity
- Arduino, Arduino Components, Input, Modules, Power, Relays
2 Channel 5v Optically Isolated Relay Module
Arduino, Arduino Components, Input, Modules, Power, Relays2 Channel 5v Optically Isolated Relay Module
- Operating Voltage: 5v DC
- Relay contact capacity: 250v AC 10A, or 30v DC 10A
- Optically Isolated from Mains
- Relay output: normally open, normally closed
- Low level Trigger
- signal input voltage range: 0-5 v
- VCC is power supply to board. JD – VCC is relay power supply (Default: JD – VCC and VCC Jumper)
- Compatible with Arduino, PIC, AVR etc
SKU: n/a - 2.4 Ghz, Arduino, Arduino Components, Modules, Wireless
SPP-C Bluetooth Module
- Bluetooth V2.1 + EDR
- Bluetooth Class 2
- Built-in PCB radio frequency antenna
- Support UART interface
- 3.3V power supply
- Status indication LED: P12
- Used to indicate the status of the Bluetooth module, LED flashing mode and Bluetooth module status corresponding to the following table:
- Mode LED Displays the module status
- (800 ms-on, 800 ms-off) waiting for pairing
- Host interrupt indication: P05
- Used to indicate whether the host is interrupted or not, the connection status is high, and other states are low.
SKU: n/a - Arduino, Arduino Components, Modules, Sensors
DS1302 RTC Real Time Clock Module
- DS1302 Real Time Clock Module
- Serial I/O interface for minimum pin count
- Wide Working Voltage: 2.0 ~ 5.5 V
- Single – byte and multi – byte transmission for clock or RAM data read/write
- TTL – compatible (Vcc) = 5 v
- Working Temperature: 0 to + 70 Deg C
- 32.768 KHz crystal oscillator
- Overall Size: Approx. 44 x 23 x 11 mm
SKU: n/a - Arduino, Arduino Components, Display, Modules, Robotics
2004 20×4 Character LCD Display Module
- Interface: I2c
- I2C Address: 0x20
- Back lit (Green with Black Character Color) (Blue with White Character Color)
- Fully Assembled and Tested Serial LCD 20×4 Module
- Display Format: 20 Characters x 4 lines
- Supply voltage: 5V
- The module can be easily interfaced with a MCU
- The module is a low-power consumption character LCD Module with a built-in controller
- Size: approx. 9.8cm x 6cm x 1.2cm
SKU: n/a - Arduino, Arduino Boards, Development Boards, Modules
Arduino MEGA2560 With CH340G
- Microcontroller Atmega2560
- Serial Controller CH340 / Ch340G
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 54 (of which 15 provide PWM Output)
- Analog Input Pins 16
- DC Current per I/O Pin 40 mA
- DC Current for 3.3V Pin 50 mA
- Flash Memory 256 KB of which 8 KB used by Bootloader
- SRAM 8 KB
- EEPROM 4 KB
SKU: n/a - Arduino, Arduino Components
51 MCU Minimum System Development Programming Board
- Support chips: ATmega16/ATmega32 and chip which pin-compatible.
- 32 I/O pin all the leads.
- Classic ATmega16/32 minimum system, eliminating the hassle of soldering.
- Crystal: The socket hole welding facilitate the buyer to replace the crystal, 8M crystal.
- Power supply: power adapter or external expansion pin power supply (not support ISP download interface power supply)
- DC-005 Power Block (supporting the transposon is 5.5*2.1mm).
- Expand outside 4 channel VCC, GND.
- Reset: Power-on reset and reset button.
- Power LED (D1) and the program run indicator (D2).
- Standard ISP download interface.
SKU: n/a - Arduino, Arduino Components, Modules, Sensors
KY-026 IR Flame Sensor Fire Detection Module
- High sensitivity IR receiver
- Extremely sensitive to wave between 760-1100nm
- Power supply indicator lamp
- Comparator output indicator lamp
- AO, real-time thermister voltage signal output
- DO, high / low electric level signal output
- Analog quantity output
- Threshold rollover electric level output
- Threshold adjusted by potentiometer
- Detection Angle Range: About 60 degrees
- Power Supply: 0-15 V DC
- Hole Inner Diameter: Approx. 3mm
- Size (L x W): Approx. 36 x 16mm
SKU: n/a - Arduino, Arduino Components, Modules, Sensors
GY-291 ADXL345 Digital 3 Axis Digital Gravity Sensor
- GY-291 ADXL345 Digital 3 Axis Digital Gravity Sensor Module for Arduino & PIC
- ADXL345 is well suited for mobile device applications. It can tilt sensing applications
- Measures the static acceleration of gravity, you can measure motion or shock resulting from moving
- State acceleration. Its high resolution (3.9mg / LSB), capable of measuring less than 1.0 °
- Tilt angle change.
SKU: n/a - Arduino, Arduino Components, Input, Modules, Sensors
Reed Magnetic Sensor Module
- Normally Open Reed
- The comparator output signals clean, good waveform, driving ability, 15mA.
- The working voltage of 3.3V-5V
- The output form: digital switching output (0 and 1)
- A fixed bolt hole for easy installation
- Small PCB board size: 3.2cm x 1.4cm
- Using a wide voltage comparator LM393
SKU: n/a - Arduino, Arduino Components, Components, LED
WS2812 RGB LED Breakout Module
- This really blew our minds to see the control IC of an individually addressable RGB LED was moved into the actual LED
- So we wanted to offer this amazing product to you
- They’re great when you need a lot of color from not a lot of board space
SKU: n/a - Arduino, Arduino Components, Sensors
DHT11 Temperature & Humidity Sensor
- DHT Series Digital Temperature and Humidity Sensor
- Full scale calibration, digital output
- Humidity Measurement Range: 20% to 9 0%RH (0-50 ° C temperature compensation)
- Temperature Measurement Range: 0 to +50 ° C
- Humidity Measurement Accuracy: Measurement Accuracy of ± 5.0% RH Temperature: ± 2 ° C
- Response time: <5 seconds
- Ultra Low Power Consumption
SKU: n/a - 2.4 Ghz, Arduino, Arduino Components, Espressif, Modules, Wireless
ESP8266 07 Wifi Module
- Improve the peripheral circuit
- Enhanced impedance matching
- Signal output is better, whether it is stable or anti jamming ability
- IPEX Connector For External Antenna
- PCB antenna after professional laboratory testing, perfect matching, after ROHS certification, have been greatly improved!
- The enhanced version is fully compatible with the firmware before the ESP-12, based on the SPI and the new six IO port
- Development is more convenient, more widely used!
- Node MCU Compatible
- Arduino IDE Compatible
SKU: n/a
