Vibration Sensor
Showing all 8 resultsSorted by popularity
- Arduino, Arduino Components, Modules, Sensors
Infrared Reflective Obstacle Avoidance Sensor
- Sensor module output port OUT can be directly connected with the microcontroller IO port.
- Can also directly drive a 5V relay; Connection: VCC-VCC; GND-GND; OUT-IO
- The Comparator with LM393, Stable.
- Can be used 3.3V-5V DC power supply module. When the power is turned on, the red power indicator light;
- VCC external 3.3V-5V voltage (can be directly connected with the 5v microcontroller or 3.3v single-chip)
- GND external GND
- OUT small board digital output interface (0 and 1)
SKU: n/a - Arduino, Arduino Components, Modules, Sensors
SW-420 Normally Closed Vibration Sensor Module
- The company produced normally closed type vibration sensor SW-420
- The comparator output, signal clean, good waveform, driving ability is strong, for more than 15 ma
- The working voltage of 3.3V to 5V
- Output form: digital switch output (0 and 1)
- Has a fixed bolt hole, convenient installation
- Small board PCB size: 3.2cm x 1.4cm
- Use the LM393 wide voltage comparator
SKU: n/a - Arduino, Arduino Components, Sensors
Soil Moisture Detection Humidity Sensor Module
- Operating Voltage 3.3V-5V
- Module Dual Output mode , a simple digital output , analog output more accurate.
- With fixed bolt hole for easy installation
- Small PCB board size : 3cm * 1.6cm
- Power Indicator ( red ) and the digital switch output Indicator ( green )
- Using LM393 Comparator Chip , Stable
- VCC external 3.3V-5V
- GND GND External
- DO small board digital output interfaces ( 0 and 1 )
- AO small board analog output interface
SKU: n/a - Arduino, Arduino Components, Modules, Sensors
SW520D Tilt Sensor Module Module
- Using high-sensitivity switch SW 520D as the sensor.
- The module is equipped with fixed bolt hole for convenient installation.
- Using LM393 wide voltage comparator,clean signal,good waveform,strong driving ability with output of more than 15 mA.
- The working voltage of 3.3V to 5V.
- Small PCB size:3.2cm x 1.4cm.
- Digital output form: digital switch output (0 and 1).
SKU: n/a - Arduino, Arduino Components, Input, Modules, Sensors
Reed Magnetic Sensor Module
- Normally Open Reed
- The comparator output signals clean, good waveform, driving ability, 15mA.
- The working voltage of 3.3V-5V
- The output form: digital switching output (0 and 1)
- A fixed bolt hole for easy installation
- Small PCB board size: 3.2cm x 1.4cm
- Using a wide voltage comparator LM393
SKU: n/a - Arduino, Arduino Components, Modules, Sensors
Infrared Reflective Obstacle Tracking Sensor TCRT5000
- Sensor module output port OUT can be directly connected with the microcontroller IO port.
- Can also directly drive a 5V relay; Connection: VCC-VCC; GND-GND; OUT-IO
- The Comparator with LM393, Stable.
- Can be used 3.3V-5V DC power supply module. When the power is turned on, the red power indicator light;
- VCC external 3.3V-5V voltage (can be directly connected with the 5v microcontroller or 3.3v single-chip)
- GND external GND
- OUT small board digital output interface (0 and 1)
SKU: n/a

STM8S103F3P6 development board Micro USB
DS1307 AT24C32 Real Time Clock module with EEPROM
HW-MS03 Microwave Radar Human Inductive Motion Sensor
RCWL-0516 Microwave Radar Human Inductive Motion Sensor
RS232 Serial COM Convert USB 2.0 to 9-Pin DB9 Male Cable
TDA2030A 18W Mono Audio Amplifier Board
AC-DC 5V 700mA 3.5W Isolated Transformer Power Supply
DB9 9 Pin Connector Case with Screws
THX203H High Performance Switch Mode Power Controller IC
78L05 LM78L05 TO-92 5V 100mA Voltage Regulator
Infrared Reflective Obstacle Tracking Sensor TCRT5000
Universal Bluetooth Audio Receiver AUX Kit for Amplifiers
USB Step UP Down 5v to 1.2v to 24v Buck Boost Converter
3144E Hall Effect Magnetic Field Sensor Module




